Classification C-2 (electrical contracting) covers wiring, fixtures and apparatus, with subclassifications for C-2a electrical wiring, C-2b integrated ceilings, C-2c fire detection, C-2d low-voltage systems, C-2f residential wiring (600 volts or less, structures up to three stories) and C-2g photovoltaics. A general building contractor may not perform electrical work without the specialty license (NRS 624.215(3)).
NRS 624.031(6)(b) carves electrical work out of the small-job exemption entirely: even a $50 fixture swap for hire is contracting that needs the license. The NSCB licenses the business through a qualifier; individual electrician certification, where required, comes from the local building department.
The state sets the license floor; the county or city permit office controls filing, inspections, and local rules wherever the job site sits.
Licensing is exclusively state — the NSCB issues every contractor classification under NRS 624, and no city or county license substitutes for it. Cities and counties issue building permits and run inspections; whenever a permit is required, the under-$1,000 handyman exemption no longer applies (NRS 624.031(6)(a)). Local business licensing is set by each jurisdiction.
The local offices section below names the exact permit desk for every Nevada county on file.
Each row names the issuing authority, cost, timeline, citation, and status behind the requirement — verified against the official source.
Published fees from the issuing authorities, as of October 2026. Local permit fees vary by project and jurisdiction — the basis is stated where a flat number does not exist.
Electrical work is excluded from NRS 624.031(6) by name — the $1,000 handyman threshold never applies.
Every Nevada license carries a monetary limit — the largest contract you may take on one site for one client — set from your financial statement. Bidding over it voids the bid; one-project increases must be approved before you bid.
Nevada licenses specialty trades most states leave unlicensed. The same $300 application, $600 biennial fee, bond, and Business & Law exam apply whether you pour concrete or wire panels.
A practical sequence for a new electrical contractor in Nevada. Actual agency processing times are noted in the ledger above.
Each item names the issuing authority, cycle, and citation.
Statutory consequences with their citations — not estimates, not “commonly cited” guesses.
Acting as a contractor or bidding without an active license; penalties escalate with each offense, and the maximum fine may be enhanced by up to 10% of the contract value if work began or money was received.
In addition to prosecution, the Board may fine each violation of the license requirement or unlawful advertising.
A bid or contract made without a license is void from the start, and an unlicensed contractor cannot sue to collect payment.
Inside city limits, the city office listed here issues the permit; the county office serves unincorporated areas. Every office links to its official page.
Every fact in this file was checked against these official sources on October 2026.
Pending verification: Whether the local building department where you work (e.g., Clark County, City of Las Vegas, Washoe County) requires individual journeyman or master certification cards for this trade — NSCB licenses the business, not individual tradespeople · Full scope text of C-2d low-voltage and C-2e (if any) subclassifications · Current PSI exam fees for the Business and Law (CMS) and trade exams (set by the testing vendor; not published in NAC 624) · Whether the Board is currently collecting the full statutory Recovery Fund assessment or a reduced amount under NRS 624.470(3) (the Board FAQ lists the full $200 / $500 / $1,000 schedule) · The NSCB General Requirements FAQ still lists older unlicensed-contracting fines (first offense 'not more than $1,000'; second $2,000–$4,000; third $5,000–$10,000). NRS 624.750(2) as amended in 2025 sets $1,000–$4,000, $4,000–$10,000 and $10,000–$20,000 — the statute is used here
General information, not legal advice. Always confirm requirements, deadlines, and forms with the issuing authority before filing or contracting.
Store licenses, permits, policies, and renewal dates in one place.